A tile trim clause is complete when it answers seven questions. The questions cover material and grade, profile, height against the tile, finish and how its consistency is judged, corners, submittals, and acceptable substitutes. Miss any one answer, and the line is not yet a specification. It is a placeholder that every bidder will price differently.
This guide is written from the document side of the table. It shows how a tile trim clause is built, and how the matching BOQ lines are measured. It also covers submittal and substitution wording, so the approved product is what arrives on site.
The subject is the writing task itself, not the buying decision behind it. If your project is still at the buying stage, our tile trim specification checklist for hotels and commercial projects works through that confirmation first.
Why Tile Trim Fails at Tender Stage
Open a real project specification and the pattern repeats. Tiles get pages of clauses: format, thickness, bedding, grout. The trim finishing every exposed edge gets one line under “Accessories,” usually a material hint and a note that colour is to be confirmed. It is treated as a site decision because each individual length is cheap.
The cost of that one line shows up later, and never in the trim itself. Bidders price different grades against the same vague description, so the comparison is distorted before work starts. The winning contractor orders whatever the local merchant stocks. When the architect rejects it at the mock-up stage, the replacement becomes a variation argument instead of a simple instruction.
A complete clause removes that sequence. It fixes the few variables that actually change the product: grade, profile, height, finish route and corner method. Everything else stays free for the contractor. The sections below take that clause apart.
Where the Clause Sits in the Tender Documents
A tile trim requirement normally lives in three places at once. The technical specification carries the quality definition. The bill of quantities carries the measured items and units. The drawings or a trim schedule carry the locations. If the three disagree, the discrepancy itself becomes a tender query or a claim.
In CSI MasterFormat projects, trim sits inside Section 09 30 00, Tiling. In NBS-based projects, it sits inside M40, the tiling work section. In both systems it usually appears as an accessories line inside a broader tiling clause. Neither system gives trim its own section, which is exactly why it gets compressed into a single line.
The practical rule follows from that. Write the full quality definition once, in the specification, and make every BOQ line reference that clause. A shortened BOQ summary will eventually contradict the clause, and contractors are entitled to price the cheaper reading.
Anatomy of a Tile Trim Specification Clause
1. Material and grade, named in full
Name the alloy or steel grade, not the metal family. “Aluminium trim” allows anything from soft commercial alloys to architectural extrusions. A clause that reads “aluminium alloy 6063, temper T5” can be priced, checked against a mill certificate and enforced. Our own range is built on 6063 and 6463, two alloys that anodize to visibly different brightness.
Stainless steel needs the same treatment, split by location. Grade 304 (EN designation 1.4301) is the normal interior grade. Grade 316 (1.4401) is the grade to name for wet areas, pools and coastal exposure, because its molybdenum content resists pitting in chloride environments. One project can carry both grades on different lines; it cannot leave the grade open and expect wet-area performance by default.
Solid brass should be specified as solid, with the grade stated — H59 in our range. “Brass finish” only describes a colour, and that colour can sit on aluminium or steel. The clause should also name the reference standard: the EN 10088 series for stainless grades, EN 755 and ASTM B221 for aluminium extrusions. The standard turns a grade name into a verifiable delivery condition.
2. Profile and height, tied to the tile
State the profile shape and the trim height for each location type. The main tile trim profiles — square edge, L-shaped, round edge and the rest — are not interchangeable details. They read differently, protect the edge differently and price differently. Where a project uses more than one profile, the trim schedule should assign each run to a profile, not leave the choice to the installer.
Trim height follows the tile, not the trim catalogue. The working rule is tile thickness plus the adhesive bed, so the finished trim face sits level with the tile face. The clause should state the tile thickness it is written against, or instruct that height be selected to suit tile plus bedding.
Our tile trim size guide works through that measurement in detail. Without the build-up, the named height can leave the trim below the tile face and the edge exposed.
3. Lengths and tolerances, by reference
State the standard length the BOQ assumes, because measurement and wastage both depend on it. Lengths of 2.44 m, 2.5 m, 2.7 m and 3.0 m are all common in the market. A rate built on one length does not convert cleanly to another. The clause should name the scheduled length per item and state whether cut lengths are acceptable.
Do not invent tolerance numbers in the clause; reference them instead. For aluminium profiles, EN 755-9 covers tolerances on dimensions and form for extruded profiles. Precision profiles in 6060 and 6063 fall under the EN 12020 series. ASTM B221 performs the same role in North American documents. The enforceable wording is “tolerances to [standard], confirmed by the manufacturer’s profile drawing at submittal stage.” That gives the QS something measurable without invented figures.
4. Finish, and how consistency will be judged
A colour name is not a finish specification. “Gold” can be anodized, PVD-coated, powder-coated or polished brass, and each route ages and cleans differently. The clause should name the finish route and the colour, in that order: anodized champagne, PVD brushed gold, powder-coated matt black. Bidders can then price the same process rather than the same word.
Consistency needs a mechanism, not an adjective. The workable mechanism is an approved reference sample, agreed before manufacture, against which production is checked. A single-batch rule for each continuous visible run closes the other door.
On the factory side, this is the control that actually holds. Repeat production is manufactured and inspected against the sealed approved sample. Drift is caught at the factory instead of argued about on site. Write both halves into the clause — the sample as the standard, rejection of out-of-limit production as the consequence.
5. Corner pieces, as their own requirement
Corners decide whether a trim installation looks manufactured or improvised. The clause should state whether corners are factory-formed corner pieces or site mitres, profile by profile. Where corner pieces are required, they must match the trim in profile, material and finish. They also belong in the BOQ as separate counted items, not inside the metre rate.
This is a small line with an outsized effect. Unspecified corners default to site-cut mitres of variable quality, and the cost of matching tile trim corner pieces appears later as an extra. Specified and measured, they are priced identically by every bidder.
6. Submittals and approval, named in the clause
Submittals only happen reliably when the specification lists them. For tile trim, the list is short. It covers the manufacturer’s profile drawing for each profile, a material certificate for the named grade, and physical samples of each profile and finish. It also covers one corner piece showing how corners will be formed. Each item answers a question the clause has already raised.
The clause should also fix the sequence: written approval of samples and data before bulk manufacture begins, not alongside it. That timing sentence makes the approved sample a production reference instead of a formality. The specification’s only job here is to make the submittals, and their timing, contractual.
7. The substitution rule
Most public tenders cannot lock a document to one supplier, so the clause needs an equivalence rule with teeth. “Or equal” on its own has none. The enforceable version defines equality: same material grade, same profile dimensions, same finish route, evidenced by samples and data sheets, approved in writing before ordering. Anything less lets a bidder win on the specified product and deliver something cheaper.
Where a proprietary product is the design basis, name it as the reference standard and keep the same evidence route for alternatives. The design intent is protected by the definition of equality, not by the brand name. If a project genuinely cannot accept substitutes, say so and say why. A phased roll-out matching earlier phases is a legitimate reason. A stated reason is what survives procurement review.
The Sample Clause, Line by Line
The wording below is a complete working example for an aluminium and stainless package. Adapt the bracketed items to the project, and keep the structure. Every sentence in it exists because a tender query or a site dispute once traced back to its absence.
Metal tile trim. Supply and install metal tile trim to all exposed tile edges shown on the drawings and listed in the trim schedule.
- Materials. Aluminium alloy 6063, temper T5, extrusion and delivery conditions to EN 755-1 and EN 755-2 (ASTM B221/B221M as equivalent). Stainless steel to the EN 10088 series: grade 1.4301 (304) in dry interiors; grade 1.4401 (316) in wet areas, pool halls and coastal locations. Solid brass H59 where scheduled. The grade for each location is stated in the trim schedule.
- Profiles and heights. [Square edge / L-shaped / round edge] as scheduled. Trim height to suit the scheduled tile thickness plus adhesive bed, so the trim face finishes level with the tile face. Standard length [2.5 m] unless otherwise scheduled.
- Tolerances. Profile dimensions and straightness to EN 755-9 for aluminium, or the EN 12020 series for precision profiles. Where no product standard applies, the manufacturer’s declared tolerances apply. Tolerances are confirmed by profile drawing at submittal stage.
- Finish. [Anodized / PVD / powder-coated], colour [reference]. Each continuous visible run to come from a single production batch, matching the approved reference sample. Material outside the agreed limit samples will be rejected.
- Corners and accessories. Factory-formed corner pieces, end caps and connectors to match the trim in profile, material and finish. Site mitres only where the schedule states them. Corners and accessories are measured separately in the bill of quantities.
- Submittals. Before manufacture: profile drawings for each profile. Material certificate for each named grade. Two sample lengths of each profile and finish. One corner piece per profile. No bulk manufacture before written approval of samples.
- Substitutions. Products offered as equal must match the grade, profile dimensions and finish route of the specified trim. Equality must be evidenced by samples and data sheets. Substitution requires written approval before ordering.
Three features of this wording do most of the work. Grades are assigned per location, so the wet-area upgrade is a drafting decision, not a site negotiation. Finishes are controlled by a physical sample and a batch rule. Corners sit in their own measured items.
Writing the BOQ Lines
The bill of quantities should mirror the clause, one measured line per distinct product. Distinct means any change of material, grade, profile, height or finish creates a new line. A single averaged “tile trim” line forces every bidder to guess the product mix, and that guess is where the tender spread comes from. Each line’s description can stay short: the clause carries the quality definition, so the line only identifies product, location and unit.
Measurement needs two decisions, and both belong in the bill preamble. First, trim lengths are measured in linear metres along the run as installed. Cutting, jointing and wastage sit either in the rate or in a stated added percentage. Second, corner pieces, end caps and connectors are counted per piece, in numbers (Nr). A corner’s cost has no relationship to the metreage around it. Mixing the two units in one line is the most common BOQ error on this product.
The example below uses the heights, lengths and finishes of typical aluminium tile trim and solid brass tile trim ranges. Quantities are illustrative.
| Item | Description | Unit | Qty (illustrative) | Measurement note |
|---|---|---|---|---|
| T1 | Square-edge aluminium tile trim, 6063-T5, anodized silver, 10 mm high, 2.5 m lengths, to bathroom wall edges; clause ref. Metal Tile Trim | m | 1,240 | Measured along the run; cutting and joints included in rate |
| T2 | Square-edge stainless steel tile trim, grade 316 (1.4401), brushed finish, 10 mm high, 2.5 m lengths, to shower and wet areas; clause ref. Metal Tile Trim | m | 380 | Measured along the run; grade stated per location |
| C1 | Factory-formed external corner pieces to T1, same profile, material and finish | Nr | 96 | Counted per piece; not included in the T1 metre rate |
| C2 | Factory-formed external corner pieces to T2, same profile, material and finish | Nr | 40 | Counted per piece; not included in the T2 metre rate |
| E1 | End caps to T1 and T2, matching finish | Nr | 60 | Counted per piece at open run ends |
Read the table as a QS would. Every line can be priced from the clause without a site visit or a phone call. Every line can also be checked on delivery against a certificate, a drawing or the approved sample. That is the test a BOQ line has to pass: priceable at tender, verifiable at delivery.
Five Specification Mistakes That Cause Variations
Writing “where necessary.” The phrase transfers the design decision to the contractor and the cost argument to the contract. Locations belong on the drawings or in the trim schedule. The clause states the product; the schedule states the places.
Specifying a colour instead of a finish route. Colour names survive; processes are what get priced and delivered. Anodized, PVD and powder-coated versions of one colour are three different products with three different service lives.
One grade for the whole project. Defaulting to the cheaper grade under-specifies the wet areas; defaulting to 316 everywhere over-specifies the dry ones. Splitting grades by location is cheap at drafting stage and expensive to argue about afterwards.
Burying corners in the metre rate. Corners then arrive as site mitres or as an extra-over claim. Counted items cost almost nothing to add, and they remove a recurring friction at final account.
Copying the last project’s clause without checking the tile. Trim height is a function of this project’s tile and bedding. A clause inherited from a project with 8 mm tiles silently under-sizes every edge on a project with 11 mm tiles.
Frequently Asked Questions
Does tile trim need its own specification section?
No. Tile trim is normally specified inside the tiling section, as a defined clause within the tiling products. That means Section 09 30 00 in CSI MasterFormat projects, or the M40 work section in NBS-based projects. It needs its own complete clause — grade, profile, height, finish, corners, submittals, substitutions. It does not need its own section number, and it should not be reduced to a single accessories line.
How is tile trim measured in a BOQ?
Trim lengths are measured in linear metres along the run as installed. The bill preamble should state whether cutting, jointing and wastage are included in the rate or added separately. Corner pieces, end caps and connectors are counted separately, per piece, because their cost is unrelated to the length of the run.
Should the clause name a manufacturer or stay performance-based?
Either works, provided equality is defined. A performance clause names the grade, profile dimensions and finish route, then allows “or equal” products that evidence the same properties with samples and data. A proprietary clause names one product as the reference standard and applies the same test to alternatives. What fails is “or equal” with no definition of equal.
What submittals should the clause require for tile trim?
Four items cover the risk. They are a profile drawing for each profile, a material certificate for each named grade, and physical samples of every profile and finish. One corner piece showing the corner method completes the set. The clause should also require written approval of samples before bulk manufacture. The approved sample then becomes the reference that production is checked against.
How do I choose between 304 and 316 in the clause?
Assign the grade by location, in the clause or the trim schedule. Grade 304 (1.4301) suits dry interior areas. Grade 316 (1.4401) should be named wherever trim faces standing water, pool chemicals, cleaning chemicals or coastal air. Its molybdenum content resists pitting in those conditions. One project commonly carries both grades on separate BOQ lines.
Conclusion
A tile trim clause is short, but it has to be complete. Name the grade per location. Fix the profile and the height against the tile build-up. Specify the finish by process and control it with an approved sample. Count the corners separately, list the submittals, and define what “equal” means.
The BOQ then mirrors the clause line for line, metres for lengths and numbers for pieces. Documents written that way price cleanly at tender and verify cleanly at delivery — which is the whole job of a specification.